Samson 45 Northumberland Style Turnkey Package Length Overall: 45’Beam: Midship: 15’3”Beam:Stern: 14'Draft: 4'Displacement: 14.27 Gross tones Name * First Name Last Name Company Name Email * Phone * Country (###) ### #### Samson 45 - Northumberland Style COMPLETE WITH: Built in spray rails, speed rails Hydrodynamic, tapered sternpost Moulded fiberglass shoe (integrated with hull) Two-piece moulded super structure from foredeck to back of wheelhouse & moulded non-skid finish Moulded fiberglass helm station Cored deck, wheelhouse and roof DESCRIPTION OF HULL & SUPER STRUCTURE BREAKDOWN Fiberglass roof with visor, laminated to wheelhouse Assembly of all cuddy bulkheads, cuddy floor, wheelhouse floor and back deck floor Assembly of gussets, vent boxes and fuel boxes All faired out, painted with ISO gel coat Waterline and trim package Bow cleat, stern and bow staples Sliding door on Teflon Track Drain plug in keel Heavy duty PVC gunwale moulding Radar Arch 8 PVC fixed windows Cost Breakdown Deck Hatches Installation - 3pcs FRP 24" x 36" - 20 x 20 Bomar hatch in cuddy - 4pcs FRP Hatches 40' x 40' - 24" x 60" aluminum boman door for engine room *Aluminum hatches optional if required Shaft Assembly Straight shaft assembly & installation complete with: - 14' 6" x 2 3/4” 316 S.S shaft with brass nut - 7ft Fiberglass shaft log - Shaft coupling - Anodes 2 3/4 - Dripless shaft system "Hy Torque propeller blade 36"" *Prices for properllers are subject to change based on economic conditions" Single station power steering complete with: - Steering unit with 15" S.S steering wheel, S.S spindle, mounting plate - Dual Ram steering unit nitrated steel piston shafts 2 1/2" - 2 1/2" S.S rudder stock and 34" x 34" x 3/8" S.S Rudder with support wings - 2 1/2" Packing box Fuel Tanks Installation - 2 S.S fuel tanks constructed with 1/8” 2B finish plate - 2” fill lines & 2” stainless steel deck fills - 1” vent lines - 1/2” Fuel Hose to engine from one tank - Shut off valve - Inter-connecting line (3/4” hose) - 3/8” return line to one tank - 2 tank whistlers - 200 Gal each Wash-down/Bailing Pump Installation - 11/2" 3-way ball valve - Bronze fittings - 1 1/2" thru hull and seacock - Reinforced PVC hoses - 2" Hydraulic Wash Down Pacer - Fire hose with Lexon nozzle and polypropylene quick disconnect fittings Electrical System Installation - Custom 20 circuit breaker panel with 100-amp main breaker and ammeter - 4 pcs Group 8D cranking battery - Battery box #2 electrical mains, #2/0 starter cables - 4 running lights (Port, starboards, stern, masthead) - Stainless steel dome lights 10pcs - 2 Pantograph windshield wipers - heavy duty - Rule 3700 GPH bilge pump, 3-way switch, float and hose - 2000 bilge pump for engine room - Deck light & Engine room Lights Engine Installation - Installation, alignment & bolting - Fiberglass engine beds - Bronze fittings, hoses & heavy-duty clamps and strainer - 8" Wet Exhaust Manual Tabsco Toilet - Toilet with 9L holding tank and Y valve to overboard Accommodations - Marine Head Enclosure - Table with benches - Top and bottom bunks - Cupboard and countertop Deck Hatches Shaft Assembly Steering Installation Fuel Tanks Wash-down/Bailing Pump Installation Electrical System Installation Engine Installation Manual Tabsco Toilet Accommodations Additional Items Available Sliding PVC Windows: Starboard and Port Side Cage Lettering Fish Holds Extra roof and side wall with closet & compartment SS Grab Rails on Wheelhouse and Cuddy Roof 1/2 Aluminum pipe on outside deck and angle on inside Extra work to modify dash 8" wet exhaust muffler Panel upgrade to PEI style AC panel invertor shore power 2pcs overhang lights 4' LED tubes Cold water tanks 15gal with sink & tap Bus heater Boom (Same as Daryls) Wear patch Bow Thruster Below deck live lobster well - Includes pumps and plumbing Additional fittings Electrical Materials Labor to install Fiberglass pump brackets Please note Customer to supply all electronics Customer to supply engine & Start-Up Customer to supply hydraulics Thank you!